Connect Tech JB2 Manual do Utilizador Página 1

Xtreme/104 Opto User's Manual, ver. 0.00 Connect Tech Inc.“Meeting your objectives ... by design” Xtreme/104 Opto Multi-port Serial Com

Xtreme/104 Opto User's Manual, ver. 0.00

Hardware Installation 5 Xtreme/104 Opto User's Manual, ver. 0.00 Hardware Installation Port Addresses Port addresses are configured wi

6 Hardware Installation Xtreme/104 Opto User's Manual, ver. 0.00 Example 1 Example 2 The following example shows the port address jumper block

Hardware Installation 7 Xtreme/104 Opto User's Manual, ver. 0.00  Mode 3 (two IRQs): 1. First you jumper position E on the JB3 jumpe

8 Hardware Installation Xtreme/104 Opto User's Manual, ver. 0.00 Example: Mode 3 – two IRQs The following example shows the settings on JB3 and

Hardware Installation 9 Xtreme/104 Opto User's Manual, ver. 0.00 Baud Rate Selection The Xtreme/104 Opto is capable of baud rates up

Xtreme/104 Opto User's Manual, ver. 0.00

Software Installation 11 Xtreme/104 Opto User's Manual, ver. 0.00 Software Installation Windows NT Windows NT and its standard serial

Xtreme/104 Opto User's Manual, ver. 0.00

Specifications 13 Xtreme/104 Opto User's Manual, ver. 0.00 Specifications Operating Environment  Storage temperature: -65° C to 150° C 

Xtreme/104 Opto User's Manual, ver. 0.00

14 Specifications Xtreme/104 Opto User's Manual, ver. 0.00 Dimensions  Xtreme/104 Opto PCB Length: 10.40 cm (4.09 inches) – includes connecto

Connectors/Pinouts 15 Xtreme/104 Opto User's Manual, ver. 0.00 Connectors/Pinouts Table 3: P4/P5/P6/P7 - 10 pin port header pinouts Pin No

16 Connectors/Pinouts Xtreme/104 Opto User's Manual, ver. 0.00 Table 4: DB-9 cable connector pinouts Pin No. RS-232 Signal Direction RS-485/

Factory Default Settings 17 Xtreme/104 Opto User's Manual, ver. 0.00 Factory Default Settings Function Factory Setting I/O Port Address JB3

Xtreme/104 Opto User's Manual, ver. 0.00

RS-232/RS-485/422 Option 19 Xtreme/104 User's Manual, ver. 0.01 RS-232/RS-485/422 Interfaces Electrical Interace Selection The Xtreme/104 Op

20 RS-232/RS-485/422 Option Xtreme/104 Opto User's Manual, ver. 0.00 Full Duplex Mode By making sure that there are no jumpers on positions

RS-232/RS-485/422 Option 21 Xtreme/104 User's Manual, ver. 0.01 Half Duplex RS-485 By jumpering positions A and C of jumper blocks JB4, JB5,

22 RS-232/RS-485/422 Option Xtreme/104 Opto User's Manual, ver. 0.00 Multi-drop Slave Mode By jumpering positions A and C of jumper blocks JB4

RS-232/RS-485/422 Option 23 Xtreme/104 User's Manual, ver. 0.01 Line Termination Jumper blocks JB4, JB5, JB6 and JB7 can terminate the trans

Waranty/Copyright/Trademarks i Xtreme/104 Opto User's Manual, ver. 0.00 Limited Warranty Connect Tech Inc. warrants to the original purc

24 RS-232/RS-485/422 Option Xtreme/104 Opto User's Manual, ver. 0.00 RS-485/422 Cable Wiring Figure 2 describes a 4 wire cabling scheme betwee

Notes 25 Xtreme/104 User's Manual, ver. 0.01

Xtreme/104 Opto User's Manual, ver. 0.00

ii Certification Xtreme/104 Opto User's Manual, ver. 0.00 Certification Xtreme/104 Opto The Xtreme/104 Opto product family is to be included i

Contents iii Xtreme/104 Opto User's Manual, ver. 0.00 Table of Contents Product Overview ...

iv Contents Xtreme/104 Opto User's Manual, ver. 0.00 List of Tables Table 1: Port address settings ...

Product Overview 1 Xtreme/104 Opto User's Manual, ver. 0.00 Product Overview The Xtreme/104 Opto adapters are high performance multi-port ser

2 Product Overview Xtreme/104 Opto User's Manual, ver. 0.00 Optical Isolation The Xtreme/104 Opto uses optocouplers and isolated DC to DC conve

Product Overview 3 Xtreme/104 Opto User's Manual, ver. 0.00 Figure 1 shows the locations of various hardware components of the Xtreme/104 Opt